YFD300100-F                   

                                     UV lamp parameters

                                                  實拍UV燈頭圖

  產品特點 Product features

1）無需預熱，即開即用;

     No preheating, ready to use
2）不含汞，既安全又環保；

     Mercury free, safe and environmentally friendly
3） 產品功率小，節能省電；

     Product power is small, energy saving
4） 設備結構簡潔大方，輕便，易集成；

    The equipment structure is simple, light and easy to integrate
5）冷光源，無熱輻射，降低了固化過程產生的熱量；

    Cold light source, no thermal radiation, reduce the heat generated during the curing process
6） 采用精密的光學分析技術,光效率密度高，均勻性高達90%以上；

    Using precise optical analysis technology, the optical efficiency density is high, and the uniformity is more than 90%
7）采用韓國LG垂直結構LED紫外燈珠，壽命長達20000小時以上。

    It adopts Korean LG vertical structure led UV lamp bead, with a service life of more than 20000 hours.

   參數設置Parameter setting

開機畫面Boot screen

按下“Welcome”按鈕畫面如下Press the "welcome" button, and the screen is as follows  

能量值：UV燈功率0-100%（Energy value: UV lamp power 0-100%）

自動模式：按下啟動UV燈亮倒計時開始，時間到燈滅。

（Automatic mode: press start UV light, countdown start, time to light out.）

手動模式：按下啟動UV燈亮，按下停止UV等滅。

（Manual mode: press to start UV light on, press to stop UV light off.）

倒計時：時間設定大于0時才會顯示

（Countdown: only when the time setting is greater than 0）

溫度：顯示銅基板上的溫度

Temperature: displays the temperature on the copper substrate

啟動：按下燈亮 （Start: press the light to light up）

停止：按下燈滅 （Stop: press the light to go out）

燈亮?xí)r按鈕指示燈亮、滅時指示燈滅

（When the light is on, the button indicator light is on, and when it is off, the indicator light is off）

   溫度超溫報警時UV燈不亮

      參數設置界面Parameter setting interface

照射時間：設置為自動模式時時間計時有效

Irradiation time: the time is valid when it is set to automatic mode

運行時間：UV燈累計時間

Running time: UV lamp cumulative time

報警溫度：設定報警時溫度，設置范圍0-100℃

Alarm temperature: set the alarm temperature, setting range 0-100 ℃

        電箱端子接線圖

UVLED be careful when using the product：

Whether the fan port is covered by other objects

Lamp cap: when using UV LED lamp cap, it is recommended to clean the glass surface of lamp cap with alcohol once a week, and use air gun or vacuum cleaner to remove excessive dust and garbage inside the controller and on the grid.

Electric box: once a month on a regular basis, use air gun or vacuum cleaner equipment to remove the dust on the fan of the electric box, so as to prevent excessive dust for a long time from reducing the heat dissipation of the electric box and reducing the service life of the electric box.

Note: before maintenance, be sure to cut off the power supply, pull out the power cord, and after maintenance, the equipment can be used only after it is completely dry to prevent danger.